Hourly rate for bench work

$125.00

Hourly rate for machine work

$150.00

Minimum charge per firearm

$40.00

Disassemble, clean, inspect, oil, reassemble and safety check firearm

Complete

• Bolt action rifle

$100.00

• Pump, auto, and lever rifles

$125.00

• AR 15 style rifle

$125.00

• Double rifles and drillings

$225.00

• Pump shotgun

$100.00

• Auto shotgun

$100.00 to $125.00

• Winchester 97, Winchester 12, Remington 11, Browning Auto-5

$175.00

• Double and O/U shotguns

$95.00 to $145.00

• Revolver

$100.00

• Auto pistol

$100.00

*Notes: Removal of heavy copper, lead, or carbon fouling

Add $20.00

AR 15 maintenance rebuild (new springs and gas rings)

Add $50.00

AR-15 style rifle service (parts not included)

• Swap out barrel

$95.00

• Thread barrel for muzzle brake

$175.00

• Install custom trigger

$45.00

• Pin and weld muzzle device

• Install accessories

Hourly Rate

• Build rifle

Hourly Rate

Clear bore obstruction

• Stuck case

$30.00 & up

• Live round

$75.00 & up

• Other than case or live round

$50.00 & up

Chamber casting

$100.00

Check headspace

$75.00

Install dovetail pistol sights (unless fitting required)

$50.00

Installation of safety (parts not included)

• Low swing safety on Mauser style rifle

$100.00

• Three position safety

$180.00

Mount scope and bore sight (excludes drilling and tapping)

• Customer supplied scope and rings

$60.00

• Lap ring

$75.00

Drill and tap barrel and/or receiver

• Standard receiver for scope mounts

$40.00 per hole

• Hard receiver for scope mounts (Springfield, Enfield, Mauser)

Price on inspection

• Open sights (front and rear)

$40.00 per hole

• Side mounts

$125.00 to $250.00

• Peep sights

$125.00

• Recrown

$150.00

• Cut and recrown

• Stripped rifle or pistol barrel

• Barreled action

• >23"

• <23"

$225.00

• Remove press fit front rifle sight

Re-barrel rifle (barrel, polishing, and bluing not included)

• Pre-threaded and pre-chambered

$175.00

• Thread, chamber, and crown

$425.00

• Install barrel liner

• Pre-threaded and pre-chambered

$200.00

• Thread, chamber, and crown

1911 Service (parts not included)

• Install and fit extended or ambidextrous safety

$100.00

• Polish barrel and feed ramp

$75.00

• Install and fit barrel bushing

$100.00

• Custom fit trigger

• Action job—3 Lb. pull

$225.00

• Install and fit match grade barrel

Quote

• Install drop in magazine well

• Drop in

• Gunsmith fit

• Drop in parts

Revolver work on S&W, Colt, Ruger, and similar

• Single action trigger job – 3Lb. pull

$225.00

• Double action trigger job – 8 to 10Lb. pull (springs not included)

$125.00

• Cut forcing cone

$125.00

• Shim cylinder to remove end shake

$125.00

Stock Work

• Barrel channel for re-barreled action in factory stock

$100.00 & up

• Other inletting

• Standard

• Install aluminum pillars and bed (pillars included)

• Basic (2-4 layers of Tru-Oil; pores unfilled, satin finish)

• Moderate (8-10 layers of Tru-oil; pores filled, flat or satin finish)

• Moderate (8-10 layers of Tru-oil, pores filled, gloss finish)

• Mask checking

• Both in wood stock

• If drilling and tapping barrel required

• Standard recoil pad

• GRACO adjustable buttplate or similar

• Shorten stock

• Lengthen stock with spacers